由于需要全部重新配置该设备所以对该设备时行了erase startup-config操作,完成后重启,发现只能进入remmon1>状态,控制板插于第5槽,flash卡插于disk1上,附操作过程!!!!!在线急等
hrbnu-c6509n>en
Password:
hrbnu-c6509n#dir
Directory of disk1:/

1 -rw- 32983632 Feb 19 2004 03:05:48 +00:00 s72033-psv-mz.122-14.SX1.bin

39911424 bytes total (6926336 bytes free)
hrbnu-c6509n#er
hrbnu-c6509n#erase ?
/all Erase all files(in NVRAM)
const_nvram: Filesystem to be erased
nvram: Filesystem to be erased
startup-config Erase contents of configuration memory

hrbnu-c6509n#erase st
hrbnu-c6509n#erase startup-config ?
<cr>

hrbnu-c6509n#erase startup-config
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
hrbnu-c6509n#
22:51:43: %SYS-SP-7-NV_BLOCK_INIT: Initialized the geometry of nvramdir
Directory of disk1:/

1 -rw- 32983632 Feb 19 2004 03:05:48 +00:00 s72033-psv-mz.122-14.SX1.bin

39911424 bytes total (6926336 bytes free)
hrbnu-c6509n#rel
Proceed with reload? [confirm]

22:51:59: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.
22:52:02: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

22:52:02: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor



22:52:02: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

22:52:05: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.



***
*** --- SHUTDOWN NOW ---
***

22:52:05: %SYS-SP-5-RELOAD: Reload requested
22:52:05: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor



22:52:05: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

System Bootstrap, Version 7.7(1)
Copyright (c) 1994-2003 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 524288 Kbytes of main memory

Autoboot: failed, BOOT string is empty
rommon 1 >
rommon 1 >
usage: dir <device>
rommon 7 > ?
alias set and display aliases command
boot boot up an external process
break set/show/clear the breakpoint
confreg configuration register utility
cont continue executing a downloaded image
context display the context of a loaded image
dev list the device table
dir list files in file system
dis disassemble instruction stream
frame print out a selected stack frame
help monitor builtin command help
history monitor command history
meminfo main memory information
repeat repeat a monitor command
reset system reset
set show all monitor variables
stack produce a stack trace
sync write monitor environment to NVRAM
sysret print out info from last system return
unalias unset an alias
xmodem x/y modem download
rommon 8 >

會不會跟 CONFIG-REG值有關 在remom模式下改下看看